Download

Open






Installation of EViRO 3d gypsum  panels

If you have decided to do the installation of EViRO 3d gypsum panels by yourself, then, please, pay attention to the following:

  1. 3d gypsum panels should be mounted on a perfectly leveled surface only
  2. Unpacked gypsum tilesshouldbe acclimatized at the job site for a minimum of 72 hours
  3. To install the panels, you will need the following materials and tools:
  • paint brush
  • roller
  • primer CT 16
  • graphite pencil
  • Knauf Perlfix gypsum adhesive
  • flat steel trowel
  • toothed trowel
  • plastic or metal flexible putty knives (scrapers)
  • sandpaper 60 - 100-grit and 100/120/150/200-grit
  • SHEETROCK Super Finish or Bostik putty
  • deep-penetration primer
  • paint
  • spray gun or compressed-air painting gun

INSTALLATION:

1. Clean the wall and apply the CT 16 primer to the leveled surface with a brush or roller.

2. Mark the walls with a graphite pencil.

3. Glue the panels to the wall with Knauf Perlfix gypsum adhesive. It should be applied to the wall with a flat steel trowel and distributed with a toothed trowel.

4. Seal the joints with Knauf Perlfix gypsum adhesive in several steps:

  • apply the adhesive using plastic or metal flexible scrapers of different  sizes (big and small)
  • work the surface with a 60 - 100-grit sandpaper for primary sanding
  • apply SHEETROCK Super Finish or Bostik putty
  • use a 100/120/150/200-grit sandpaper for smoothing and finishing the surface.

5. Prime the panels with a deep-penetration primer. This should be done before painting.

6. Cover the 3d panels with several coats of paint depending on its type. At this stage, a spray gun or compressed-air painting gun is required.

 

The EViRO factory sends installation instructions upon request.  If you need them, please, fill out the form below indicating the reference number of your contract with EViRO.

WARNING:

EViRO is not responsible for cases of not following the instructions provided or using poor-quality non-recommended materials by unqualified workers.



Портфолио ЕВиРО

Монтаж выполнен высококвалифицированными специалистами компании ЕВиРО

Gypsum 3d panels EViRO
Gypsum 3d panels EViRO

Oak 3d panels EViRO
Oak 3d panels EViRO

Soft panels EViRO
Soft panels EViRO

Gypsum 3d partitions EViRO
Gypsum 3d partitions EViRO

Gypsum lighting fixtures EViRO
Gypsum lighting fixtures EViRO

Gypsum 3d panels EViRO with lighting
Gypsum 3d panels EViRO with lighting







Built-in lighting
Gypsum moldings
Gypsum lighting fixtures
Leave your contacts and we will contact you





 
Central salon of the factory EViRO:
The Republic of Belarus, Minsk, Independence Avenue 196, shop factory "Decorative 3D panels EViRO"
+375 29 376-63-49, +375 29 378-63-01
+375 33 376 63-49, +375 33 378-63-01
E-mail: info@eviro.by
Opening hours: from 9:00 a.m. till 8:00 p.m. (without breaks and days-off)
E-mail: info@eviro.by
 
 
 
 
 
 
Central salon of the factory EViRO:
The Republic of Belarus, Minsk, Independence Avenue 196, shop factory "Decorative 3D panels EViRO"
+375 29 376-63-49, +375 29 378-63-01
+375 33 376 63-49, +375 33 378-63-01
E-mail: info@eviro.by
Opening hours: from 9:00 a.m. till 8:00 p.m. (without breaks and days-off)